Asbestos Abatement

Many Chicago-suburb homes built before 1990 still hold asbestos in floor tile, pipe insulation, textured ceilings, and siding — and a water or fire loss is exactly when it gets disturbed. We test before demolition, contain and remove it legally, and keep your restoration moving with one point of contact.

Where asbestos hides

You cannot identify asbestos by sight — only lab testing confirms it. These are the usual suspects we sample before any tear-out touches them:

  • ▸9"×9" floor tile and the black mastic beneath it
  • ▸Pipe wrap, duct wrap, and boiler insulation
  • ▸Popcorn and textured ceilings, older joint compound
  • ▸Vermiculite attic insulation
  • ▸Cement-asbestos siding and roofing
  • ▸Old vinyl sheet flooring and its backing

How abatement runs

Safe, legal, and documented — then the rest of your restoration continues without you juggling a second company.

  1. Accredited sampling and lab analysis of suspect materials
  2. Written scope — and claim coordination when a covered loss disturbed it
  3. Sealed containment with negative air and HEPA filtration
  4. Licensed crews remove the material using wet methods
  5. Sealed, labeled, and legally disposed at an approved facility
  6. Air clearance testing before containment comes down
  7. Restoration and rebuild continue on the same project, same manager

Why it belongs inside your restoration project

The worst time to discover asbestos is mid-demolition — work stops, the schedule slips, and now you are hunting for an abatement company while your home sits open. Because we test suspect materials before the tear-out starts, abatement gets planned into the project instead of derailing it.

One point of contact holds the whole scope: testing, abatement, mitigation, and the rebuild — and one claim file goes to your carrier with all of it documented. You never coordinate between an abatement contractor, a mitigation crew, and a rebuild GC. That is our job.

Suspect material in your project?

Free assessment across the Chicago suburbs. If your renovation or restoration touches pre-1990 materials, get it tested before it gets disturbed.

Call Now for Emergency Help(224) 454-4376

Insurance claim coordination from day one. We are not a "preferred vendor" — you choose us.

Asbestos Abatement FAQs

How do I know if my home has asbestos?

If your home was built before about 1990, assume some materials may contain it until tested: 9"×9" floor tile and the black mastic under it, pipe and boiler insulation, popcorn and textured ceilings, vermiculite attic insulation, cement siding and roofing, and some drywall joint compounds. You cannot tell by looking — only lab analysis of a sample confirms it. We coordinate accredited sampling and lab testing before any suspect material is disturbed.

Why does asbestos come up during water or fire damage restoration?

Because restoration means removing damaged materials — and in Illinois, suspect materials must be tested before demolition disturbs them. A flooded basement with 9×9 tile, a fire-damaged ceiling with textured coating, or a burst pipe wrapped in old insulation all trigger testing before the tear-out can legally proceed. Finding it early protects your family and keeps the project legal and on schedule.

Is asbestos removal covered by insurance?

Often, yes — when a covered loss (water, fire, storm) disturbs asbestos-containing material, the abatement required to complete the repair is typically part of the claim. We document the testing, include abatement in the scope we write for your carrier, and handle the claim coordination like any other part of the project. No promises about any specific policy — but we fight for the full scope.

Is it safe to stay home during abatement?

Work areas are fully contained under negative air pressure, with sealed barriers and HEPA filtration, so occupants can usually remain in unaffected parts of the home. For larger jobs — whole-basement flooring or attic vermiculite — we will tell you honestly if a short stay elsewhere makes sense. Containment comes down only after the work area passes clearance.

What does the abatement process look like?

Sampling and lab confirmation first. Then containment: sealed poly barriers, negative air machines, and HEPA filtration around the work area. Licensed crews remove the material using wet methods, seal it in labeled disposal bags, and transport it to a facility approved for asbestos waste. Air clearance testing confirms the area is safe before containment comes down — then the rest of your restoration continues.

Get Your Free Assessment

Tell us about your situation. Our team will contact you within one hour to discuss restoration options and next steps.

Prefer we call you?

Drop your number and a live person calls you back — usually within minutes.

By requesting a callback you agree we may call or text this number about your request.

0/500 characters

Your information is secure and will only be used to contact you about your restoration needs.